Pneumatic interfacing fluorine butterfly valve
Nominal Diameter:DN50～1000mm
Nominal Pressure:0.6~1.6MPa
Body Material : Ductile cast steel, cast steel, stainless steel +F46
Applicable temperature: -30～+70°C
Applicable medium: all kinds of strong corrosion Medium
I. Pneumatic lining fluorine butterfly valve products
Pneumatic lining fluorine butterfly valve adopts PTFE lined lining plate with spherical sealing surface. Pneumatic lining fluorine butterfly valve is easy to operate, with tight sealing performance and long service life; it can be used for quick cutting or adjusting flow. Pneumatic-lined PTFE butterfly valves are suitable for applications where reliable sealing and good adjustment characteristics are required. The valve body adopts split type, and the seal of the two ends of the valve shaft is controlled by the rotating base surface between the butterfly plate and the valve seat and the fluoro rubber; and the valve shaft is not in contact with the fluid medium in the cavity. Pneumatic lining PTFE butterfly valves are widely used in the transportation of liquids and gases (including steam) in various types of industrial pipelines. There are occasions where severe corrosive media are used, such as: sulfuric acid, hydrofluoric acid, phosphoric acid, chlorine, alkali, and king Water and other highly corrosive media.
Fully lined with PTFE (F4), polychlorotrifluoroethylene (F3) and polyfluorinated ethylene propylene (F46) fluorine plastic lining butterfly valves, with corrosion resistance, no leakage, long life and other advantages. Lined PTFE pneumatic butterfly valve is suitable for concentrated sulfuric acid, hydrochloric acid, nitric acid, hydrofluoric acid, aqua regia, various organic acids, strong acids, oxidizing medium or high-temperature olefinic sulfuric acid, high temperature concentrated acetic acid, alternating acid and alkali and various organic solvents and other Strong corrosive media.
Pneumatic Fluorine Butterfly Valve main features:
1, small and lightweight, easy to disassemble and repair, and can be installed in any position.
2, the structure is simple, compact, 90 ° turn quickly open.
3, the operating torque is small, effortless and light.
4. The flow characteristics tend to be linear and the regulation performance is good.
5, sealing material, anti-aging, corrosion resistance, applicable to a variety of media.
Second, the main technical parameters of pneumatic lined fluorine butterfly valve
1, valve body
| Body form | Straight cast butterfly valve |
| Nominal diameter | DN50～1000mm |
| Nominal pressure | PN1.0, 1.6 MPa |
| Flange standard | JIS B220, JB/T79, ANSI B16.5-1981, GB/T9113, HG20594-97, HG20618-97, etc. |
| Connection Type | Flange, clip type |
| Valve cover form | One-piece |
| Capping type | Gland compression type |
| Seal packing | V-type PTFE packing, flexible graphite packing |
2, valve trim
| Valve plate form | Vertical plate (butterfly) |
| Flow characteristics | Linear |
3, the executing agency
| Actuator model | GT Series, SR Series, AT Series, AW Series Single and Double Acting Pneumatic Actuators |
| Supply pressure | 400～700KPa |
| Air interface | G1/4"、G1/8"、G3/8"、G1/2" |
| 環境溫度 | -30～+70℃ |
| 作用形式 |
單作用執行機構：氣關式(B)--失氣時閥位開(FO)；氣開式(K)--失氣時閥位關(FC) 雙作用執行機構：氣關式(B)--失氣時閥位保持(FL)；氣開式(K)-- 失氣時閥位保持(FL) |
| 可配附件 | 定位器、電磁閥、空氣過濾減壓器、保位閥、行程開關、閥位傳送器、手輪機構等 |
三、氣動襯氟蝶閥主要性能指標
| 公稱通徑 | DN（mm） | 50～1600 | ||
|---|---|---|---|---|
| 公稱壓力 | PN（MPa） | 0.6 | 1.0 | 1.6 |
| 試驗壓力 | 強度試驗 | 0.9 | 1.5 | 2.4 |
| 密封試驗 | 0.66 | 1.1 | 1.76 | |
| 氣密封試驗 | 0.6 | 0.6 | 0.6 | |
| 適用介質 | 各類強腐蝕性介質 | |||
四、氣動襯氟蝶閥零件材料
| 零件名稱 | 材料 |
|---|---|
| 閥體 | (球墨鑄鋼、鑄鋼、不銹鋼)+F46 |
| 蝶板 | (灰鑄鐵、球墨鑄鋼、鑄鋼、不銹鋼及特殊材料)+F46 |
| 閥桿 | 2Cr13、不銹鋼 |
| 填料 | O型圈、柔性石墨 |
外形連接尺寸
| 公稱通徑 DN(mm) | 50 | 65 | 80 | 100 | 125 | 150 | 200 | 250 | 300 | 350 | 400 | 450 | 500 | 600 | 700 | 800 | 900 | 1000 | |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| L | 90 | 90 | 100 | 115 | 130 | 140 | 150 | 250 | 270 | 290 | 310 | 330 | 350 | 390 | 430 | 470 | 500 | 550 | |
| L1 | 43 | 46 | 49 | 56 | 64 | 70 | 71 | 76 | 83 | 92 | 102 | 113 | 127 | 154 | 165 | 190 | 203 | 216 | |
| H | 法蘭式 | 63 | 70 | 83 | 105 | 115 | 137 | 164 | 206 | 230 | 248 | 289 | 320 | 343 | 413 | 478 | 525 | 585 | 640 |
| 對夾式 | 63 | 70 | 83 | 105 | 115 | 137 | 164 | 206 | 230 | 248 | 289 | 320 | 343 | 413 | 478 | 525 | 585 | 640 | |
| n-φd | 4-18 | 4-18 | 8-18 | 8-18 | 8-18 | 8-22 | 12-22 | 12-26 | 12-26 | 16-26 | 16-30 | 20-30 | 20-33 | 20-36 | 24-36 | 24-39 | 28-39 | 28-42 | |
| H1 | 根據所配執行機構而定 | ||||||||||||||||||
| A | 根據閥門所需力矩而定，配置機型不同，外形尺寸也不相同 | ||||||||||||||||||
| D | 165 | 185 | 200 | 220 | 250 | 285 | 340 | 405 | 460 | 520 | 580 | 640 | 715 | 840 | 910 | 1025 | 1125 | 1255 | |
| D1 | 125 | 145 | 160 | 180 | 210 | 240 | 295 | 355 | 410 | 470 | 525 | 585 | 650 | 770 | 840 | 950 | 1050 | 1170 | |
Note: The dimensions in the table are without standard attachment data. In addition, due to possible changes in product innovation technology innovation parameters, please consult the company's technical department for the latest data.
No.31011802002466
